0 Item in list
Get a personalized quote on selected items or email the list to a colleague or just to yourself for later viewing.
OK
Model 42112
Wet Tensile Tester

The Wet Tensile Strength Tester determines tensile strength of the condensation zone that is created in all clay bonded molds during and after pouring. The wet tensile strength is determined by pul... View Full Description

Items can be emailed to you or submitted for a personalized quote.
Watch Video
FULL DESCRIPTION

The Wet Tensile Strength Tester determines tensile strength of the condensation zone that is created in all clay bonded molds during and after pouring. The wet tensile strength is determined by pulling a detachable ring from a special specimen tube. The specimen tube with the detachable ring in position is loaded with molding sand and compacted to the proper specimen height using a Sand Rammer, Model No. 42100, Pneumatic Sand Squeezer, Model No. 42117 or the Digital Pneumatic Squeezer, Model No 42160. After the start button is pressed, an elevation table raises the specimen tube. The heating plate generates steam at the sand heater interface and a temperature gradient through the sand specimen. The steam is driven away from the heating plate through the porosity of the specimen. This water vapor migrates back into the specimen to a temperature zone where it condenses. This condensation zone is known as the wet layer. After a selected time elapses, the elevation table lowers applying a tensile load to the sand specimen. Since the wet layer is the weakest area of the specimen, when a load is applied the specimen breaks at that point. The load required to break this wet layer is the wet tensile strength. The instrument is fully automatic and displays the tensile results in an easy to read digital display. The Wet Tensile Strength Tester includes the specimen tube and detachable ring, pneumatic regulator/filter, pneumatic hose and connectors to connect the supplied regulator/filter to the instrument.

FULL DESCRIPTION
AFS:Part No. 0042112-ASM
Part No. 0042112-ASM-220
 
Metric:Part No. 0042112-M-ASM-1
Part No. 0042112-M-ASM
SAND CASTING PROCESS
Process: Clay Bonded Sand
SPECIFICATIONS
  • Part Number:
  • Compressed Air:
  • Power Requirements:
  • Length:
  • Width:
  • Height:
  • Weight:
 
  • Part Number
    0042112-ASM
  • Compressed Air:
    7 bar (100 psi)
  • Power Requirements:
    100-120 Volts, 50/60 Hz
  • Length:
    17.5" / 445mm
  • Width:
    12.25" / 311mm
  • Height:
    19" / 483mm
  • Weight:
    110lb / 50kg
 
  • Part Number
    0042112-ASM-220
  • Compressed Air:
    7 bar (100 psi)
  • Power Requirements:
    220-240 Volts, 50/60 Hz
  • Length:
    17.5" / 445mm
  • Width:
    12.25" / 311mm
  • Height:
    19" / 483mm
  • Weight:
    110lb / 50kg
 
  • Part Number
    0042112-M-ASM-1
  • Compressed Air:
    7 bar (100 psi)
  • Power Requirements:
    100-120 Volts, 50/60 Hz
  • Length:
    17.5" / 445mm
  • Width:
    12.25" / 311mm
  • Height:
    19" / 483mm
  • Weight:
    110lb / 50kg
 
  • Part Number
    0042112-M-ASM
  • Compressed Air:
    7 bar (100 psi)
  • Power Requirements:
    220-240 Volts, 50/60 Hz
  • Length:
    17.5" / 445mm
  • Width:
    12.25" / 311mm
  • Height:
    19" / 483mm
  • Weight:
    110lb / 50kg

We use cookies to help us understand how you use our website. By continuing to browse, you are consenting to the use of cookies. For more information, read our Cookie Policy.

The cookie settings on this website are set to "allow cookies" to give you the best browsing experience possible. If you continue to use this website without changing your cookie settings or you click "Accept" below then you are consenting to this.

Close